Question 1

What systems do the G2/G4 and G3/G5 support?

Accepted Answer

The G2/G4 supports multiple P25 systems, including Conventional, P25 Trunking, and P25 Conventional. The G3/G5 supports everything the G2/G4 supports in addition to 2 Tone, 5 Tone and MDC 1200 on either of its two bands. They support:

Multiple IDs
2 Tone, 5 Tone and MDC 1200 (G5 Only)
Site Trunking
Full Spectrum Scan
Linear Simulcast Modulation for Simulcast Applications
Priority TGIDs
Multi-select
800 MHz, 20 kHz channel spacing, and 4 kHz deviation for Direct mode communications

Question 2

Can the G-Series P25 Voice Pagers "scan" a defined trunking frequency (Example: 855.9875, 856.2625, 857.2625, 858.2625)? If so, can you scan defined TALKGROUPS on those frequencies?

Accepted Answer

Yes, TGIDs are assigned along with the Control Channels and Site Information (site information is used to further validate that the pager is assigned to that site(s) in situations where Control Channels are reused in the network). The G2/G3/G4/G5 can be pre-programmed with Control Channels and, when first turned on, will scan for the active Control Channel. Once it is on an active Control Channel it stays there until the Bit Error Rate exceeds a predetermined value.

Question 3

Can the G3/G5, in 2 Tone mode, replace my Minitor?

Accepted Answer

Absolutely. The G3/G5 does everything the Minitor does and much, much more.
The G3/G5 supports many more RF Channels, with and without PL/DPL, and 2 Tone IDs than the Minitor. With an eight position Selector Knob switch one can configure the G3/G5 for more configurations. The Unication pagers are also rated IP67 (water and dust proof) and designed for rugged Public Safety environments. The G3/G5 Voice Pagers ensures reliable operation.

Question 4

Will the G-Series P25 Voice Pagers work on VHF or UHF Trunked Systems?

Accepted Answer

Yes, the receiver covers a fairly broad band that should cover the Control and Traffic Channel frequency range.

Question 5

Do the G-Series Voice Pagers support P25 Phase I and Phase II?

Accepted Answer

Yes! All P25 devices are Phase I and Phase II compatible.

Question 6

What type of encryption is supported?

Accepted Answer

The G2-G5 P25 Voice Pager supports the AES 256-bit P25 encryption standard, DES (Data Encryption Standard), and URC4 encryption (compatible with ARC4/ADP). The unit supports up to 1024 keys and there is a software utility used to program encryption keys into the pager so you can perform testing.

Please contact your Authorized Dealer for the utility and user guide.

nication USA

FAQ - Frequently Asked Questions

Answers to some of the most frequently asked questions about G-Series P25 Voice Pagers!

G2-G5 Frequently Asked Questions

What systems do the G2/G4 and G3/G5 support?

Can the G-Series P25 Voice Pagers "scan" a defined trunking frequency (Example: 855.9875, 856.2625, 857.2625, 858.2625)? If so, can you scan defined TALKGROUPS on those frequencies?

Can the G3/G5, in 2 Tone mode, replace my Minitor?

Will the G-Series P25 Voice Pagers work on VHF or UHF Trunked Systems?

Do the G-Series Voice Pagers support P25 Phase I and Phase II?

What type of encryption is supported?

G-SERIES P25 VOICE PAGERS PROGRAMMING RESOURCES:

DO YOU HAVE A QUESTION NOT ANSWERED IN THE FAQ?

nication​ USA

FAQ - Frequently Asked Questions

Answers to some of the most frequently asked questions about G-Series P25 Voice Pagers!

G2-G5 Frequently Asked Questions

What systems do the G2/G4 and G3/G5 support?

Can the G-Series P25 Voice Pagers "scan" a defined trunking frequency (Example: 855.9875, 856.2625, 857.2625, 858.2625)? If so, can you scan defined TALKGROUPS on those frequencies?

Can the G3/G5, in 2 Tone mode, replace my Minitor?

Will the G-Series P25 Voice Pagers work on VHF or UHF Trunked Systems?

Do the G-Series Voice Pagers support P25 Phase I and Phase II?

What type of encryption is supported?

G-SERIES P25 VOICE PAGERS PROGRAMMING RESOURCES:

​

DO YOU HAVE A QUESTION NOT ANSWERED IN THE FAQ?

nication USA